Skip to content

Pressure in Solids and Liquids Explained: p = F/A and p = ρgh

How pressure works in solids and liquids: using p = F/A, converting areas to m², why pressure grows with depth, and why the shape of the container does not matter.

Published · 7 min read

On this page

Pressure tells you how concentrated a force is. It is the force acting at right angles to a surface, divided by the area of that surface:

p=FAp = \frac{F}{A}

Here p is the pressure in pascals (Pa), F is the force in newtons (N) and A is the area in square metres (m²). One pascal is one newton per square metre. A big force on a small area gives a high pressure. The same force spread over a large area gives a low pressure.

In a liquid, the pressure gets bigger as you go deeper. The pressure caused by the liquid depends on the depth h, the density of the liquid ρ and the gravitational field strength g:

p=ρghp = \rho g h

It does not depend on the shape or the width of the container. This guide explains both equations, with worked examples and the unit conversions that catch many students out.

How do you convert cm² and mm² to m²?

Areas in questions are often given in cm² or mm². You must change them to m² before you use p = F/A.

A square 1 m wide is 100 cm wide. So its area is 100 × 100 = 10 000 cm². In the same way, 1 m² is 1000 × 1000 = 1 000 000 mm².

  • cm² to m²: divide by 10 000. For example, 250 cm² = 0.025 m².
  • mm² to m²: divide by 1 000 000. For example, 4.0 mm² = 4.0×10−6 m24.0 \times 10^{-6}\ \text{m}^2.

Worked example 1: boots and snowshoes

A hiker in the mountains of Gilgit-Baltistan has a weight of 735 N. Standing on snow, their two boots have a total contact area of 500 cm². With snowshoes on, the contact area is 3500 cm². Find the pressure on the snow in each case.

Given: F = 735 N, A = 500 cm² = 0.0500 m² (boots) or 3500 cm² = 0.350 m² (snowshoes)

Equation: p=FAp = \dfrac{F}{A}

Boots: p=7350.0500=14 700 Pap = \dfrac{735}{0.0500} = 14\,700\ \text{Pa}, or about 15 kPa (2 significant figures)

Snowshoes: p=7350.350=2100 Pap = \dfrac{735}{0.350} = 2100\ \text{Pa}, or 2.1 kPa

The area is 7 times bigger, so the pressure is 7 times smaller. The snow can support this lower pressure, so the hiker does not sink in.

Why do knives cut and snowshoes work?

The same idea explains many everyday objects. A small area gives a high pressure:

  • A sharp knife has a very thin edge. The force you apply is concentrated, so the knife cuts easily.
  • Needles, nails and the point of a drawing pin push into materials for the same reason.
  • Football boot studs and running spikes grip the ground.

A large area gives a low pressure:

  • Snowshoes and skis stop people sinking into snow.
  • Camels in the Thar Desert have wide, flat feet that do not sink far into soft sand.
  • Tractors have wide tyres, so they do not sink into muddy fields.
  • The flat head of a drawing pin spreads the force over your thumb, so it does not hurt.

Here are some numbers. Suppose you press on a knife with a force of 20 N. If the sharp edge touches the food over 0.50 mm², the pressure is 200.50×10−6=4.0×107 Pa\dfrac{20}{0.50 \times 10^{-6}} = 4.0 \times 10^7\ \text{Pa}. A blunt knife with an edge area of 5.0 mm² gives only 4.0×106 Pa4.0 \times 10^6\ \text{Pa}, which is ten times less. So you have to press much harder.

In the pressure in solids simulation, stand the same block on each of its faces in turn and watch how the pressure responds.

Why does pressure increase with depth?

Imagine a column of liquid above a small flat area A, at a depth h. The liquid in the column has to be held up by the area below it.

  • The volume of the column is A × h.
  • Its mass is density × volume = ρAh.
  • Its weight is mass × g = ρAhg.

Pressure is force divided by area, so:

p=ρAhgA=ρghp = \frac{\rho A h g}{A} = \rho g h

The area A cancels out. This is why the width and shape of the container do not matter. A narrow pipe and a wide swimming pool, both filled with water to a depth of 2.0 m, have the same pressure at the bottom. In each case, the water causes a pressure of 1000 × 9.8 × 2.0 = 19 600 Pa, or about 20 kPa. The pool holds far more water, but it spreads that weight over a far bigger floor.

Three more facts are worth learning:

  • At any depth, the pressure acts equally in all directions: down, sideways and up. This is why water spurts out of a hole in the side of a bottle, and faster from a lower hole.
  • A denser liquid gives a bigger pressure at the same depth. Seawater (about 1030 kg/m³) gives slightly more than fresh water (1000 kg/m³).
  • The equation gives the pressure caused by the liquid only. The total pressure also includes the atmosphere pushing on the surface, about 1.0×105 Pa1.0 \times 10^5\ \text{Pa}.

Why are dams thicker at the bottom?

The pressure of the water is greatest at the bottom of a reservoir, so the wall must be strongest there. Large dams, such as the Hoover Dam in the US and the Tarbela Dam in Pakistan, are much thicker at the base than at the top.

Worked example 2: the bottom of a dam

The water behind a dam is 60 m deep. Find the pressure caused by the water at the bottom. Then find the force on a 2.0 m² hatch at the bottom of the dam wall. The density of water is 1000 kg/m³ and g = 9.8 N/kg.

Given: h = 60 m, ρ = 1000 kg/m³, g = 9.8 N/kg

Equation: p=ρghp = \rho g h

Substitution: p=1000×9.8×60p = 1000 \times 9.8 \times 60

Answer: p = 588 000 Pa, or about 5.9×105 Pa5.9 \times 10^5\ \text{Pa} (2 significant figures)

Force on the hatch: rearrange p = F/A to get F = pA.

F=588 000×2.0=1 176 000 NF = 588\,000 \times 2.0 = 1\,176\,000\ \text{N}

That is about 1.2×106 N1.2 \times 10^6\ \text{N}, roughly the weight of 120 tonnes.

What happens to a diver as they go deeper?

In seawater, the pressure rises by about 100 kPa for every 10 m of depth. That is about the same as the pressure of the whole atmosphere at sea level. You can check this by rearranging the equation: h=pρg=100 0001030×9.8=9.9 mh = \dfrac{p}{\rho g} = \dfrac{100\,000}{1030 \times 9.8} = 9.9\ \text{m}.

Divers feel this pressure on their ears and need special training to go deep. Submarines need thick, strong hulls.

Worked example 3: a diver

A diver off the coast of Mombasa, Kenya, swims 25 m below the surface. The density of seawater is 1030 kg/m³. Find the pressure caused by the water. Then find the total pressure on the diver, if atmospheric pressure is 1.0×1051.0 \times 10^5 Pa.

Given: h = 25 m, ρ = 1030 kg/m³, g = 9.8 N/kg

Equation: p=ρghp = \rho g h

Substitution: p=1030×9.8×25p = 1030 \times 9.8 \times 25

Answer: p = 252 350 Pa, or about 2.5×105 Pa2.5 \times 10^5\ \text{Pa} (2 significant figures)

Total pressure: 252 350 + 100 000 = 352 350 Pa, or about 3.5×105 Pa3.5 \times 10^5\ \text{Pa}

To see how depth and density each change the pressure, try the liquid pressure and depth simulation.

Common mistakes

  • Dividing cm² by 100. Divide by 10 000 to get m².
  • Using mass instead of weight. Pressure needs a force in newtons. Multiply a mass in kg by g first.
  • Leaving the depth in cm. Use metres in p = ρgh.
  • Thinking a wider container gives more pressure. Only depth, density and g matter.
  • Mixing up the two pressures. Add atmospheric pressure only when the question asks for the total pressure.
  • Using the whole surface area of an object. Use only the area in contact with the surface.

Key points

  • Pressure is force per unit area: p=FAp = \dfrac{F}{A}, measured in pascals (1 Pa = 1 N/m²).
  • A small area gives a high pressure (knives, needles). A large area gives a low pressure (snowshoes, wide tyres).
  • 1 m² = 10 000 cm² = 1 000 000 mm².
  • The pressure caused by a liquid is p=ρghp = \rho g h. It increases with depth and with density.
  • Liquid pressure acts in all directions and does not depend on the shape of the container.
  • Total pressure under water = atmospheric pressure + ρgh.