Skip to content

Pressure in Liquids and Depth: p = hρg, Water Towers, Blood Pressure and Upthrust

Go beyond the basic equation: use pressure differences between two depths, explain water towers, blood pressure readings, manometers and water jets, and see how a difference in pressure creates upthrust.

Published · 8 min read

On this page

Pressure in a liquid gets bigger as you go deeper. At any depth, the liquid has to hold up the weight of all the liquid above it. More depth means more liquid overhead, so more pressure. For a liquid of density ρ, the pressure caused by a column of height h is:

p=hρgp = h \rho g

Here p is in pascals (Pa), h is in metres (m) and ρ is in kg/m³. The gravitational field strength, g, is in N/kg. Many books write the same equation as p = ρgh.

In real problems, what usually matters is the difference in pressure between two depths, Δp=ρgΔh\Delta p = \rho g \Delta h. This difference decides how strongly water flows from a tap, why blood pressure is measured level with the heart, and why objects in water feel an upward push. At any point in a liquid, the pressure pushes equally in every direction.

Why does pressure rise steadily with depth?

Liquids are almost impossible to squash. Water at the bottom of a deep lake has almost the same density as water at the top. So every extra metre of depth adds the same amount of pressure:

  • Fresh water (ρ = 1000 kg/m³): 1000 × 9.8 × 1.0 = 9800 Pa for every metre
  • Seawater (ρ ≈ 1030 kg/m³, a typical value): about 10 100 Pa for every metre

A graph of liquid pressure against depth is a straight line through the origin. If you include the atmosphere pressing on the surface, the line starts at about 1.0×1051.0 \times 10^5 Pa instead of zero.

Air behaves differently. It is easy to compress, so it gets thinner as you go up. That is why the equation works well for liquids, but only for small height changes in air.

The deepest point in the oceans, in the Mariana Trench in the Pacific, is about 11 km down. The equation gives 1030×9.8×11 000≈1.1×1081030 \times 9.8 \times 11\,000 \approx 1.1 \times 10^8 Pa, more than 1000 times the pressure of the atmosphere. Seawater squashes slightly at such depths, so treat this as an estimate.

How do you find the pressure difference between two depths?

Use Δp=ρgΔh\Delta p = \rho g \Delta h, where Δh is the vertical distance between the two points. If a pipe slopes or bends, its length does not matter. Only the difference in height counts.

The shape and width of the container make no difference either. A narrow tube and a wide tank, filled to the same depth with the same liquid, have the same pressure at the bottom.

It follows that points at the same level in a connected body of liquid have the same pressure. This is why water settles at the same height in every part of a U-shaped tube. Builders use the idea with a clear hose full of water: the water in each end settles at exactly the same level, so they can mark level points on opposite walls of a room.

Worked example 1: a water tower

In a town in Rajasthan, India, the water surface in a tank on a tower is 28 m above the ground. The pipes are full and no tap is open. Find the water pressure, above atmospheric pressure, at (a) a tap at ground level and (b) a tap in a third-floor flat, 9.0 m above the ground.

Given: g = 9.8 N/kg, and water has ρ = 1000 kg/m³

Equation: p=hρgp = h \rho g, where h is the height of water above the tap

(a) Substitution: p=28×1000×9.8p = 28 \times 1000 \times 9.8

Answer: p = 274 400 Pa, or about 2.7×1052.7 \times 10^5 Pa (2 significant figures)

(b) Height of water above the tap: 28 − 9.0 = 19 m

Substitution: p=19×1000×9.8p = 19 \times 1000 \times 9.8

Answer: p = 186 200 Pa, or about 1.9×1051.9 \times 10^5 Pa

The higher the tap, the lower the pressure. A tap 28 m up, level with the water surface, would get no flow at all. This is why many buildings in New York taller than about six storeys have a water tank on the roof, filled by a pump. Once water starts to flow, friction in the pipes lowers the pressure at the tap a little more.

Why is blood pressure measured level with the heart?

Your blood vessels hold a column of liquid too. The heart sets the pressure at its own level, but every point below the heart has extra pressure from the blood above it, and every point above has less. Blood has a density of about 1060 kg/m³.

Doctors give blood pressure in millimetres of mercury (mmHg), where 1 mmHg is about 133 Pa. A nurse wraps the cuff round your upper arm and keeps it at about the height of your heart. If your arm hangs down or is held up high, the reading is wrong.

Worked example 2: ankle and head

A standing adult's ankles are 1.3 m below their heart, and the top of their head is 0.40 m above it. Find how much higher the blood pressure is in the ankle, and how much lower it is in the head, than at heart level.

Given: ρ ≈ 1060 kg/m³, g = 9.8 N/kg, Δh = 1.3 m (ankle) and 0.40 m (head)

Equation: Δp=ρgΔh\Delta p = \rho g \Delta h

Ankle: Δp=1060×9.8×1.3=13 504 Pa\Delta p = 1060 \times 9.8 \times 1.3 = 13\,504\ \text{Pa}, or about 1.4×1041.4 \times 10^4 Pa (roughly 100 mmHg higher)

Head: Δp=1060×9.8×0.40=4155 Pa\Delta p = 1060 \times 9.8 \times 0.40 = 4155\ \text{Pa}, or about 4.2×1034.2 \times 10^3 Pa (roughly 31 mmHg lower)

A typical peak reading at heart level is about 120 mmHg, so a standing person's ankle can reach about 220 mmHg. Giraffes, whose heads are about 2 m above their hearts, need around twice our blood pressure to push blood up to their brains.

How does a pressure difference cause upthrust?

Think about a box held under water. Its bottom face is deeper than its top face, so the water pushes up on the bottom harder than it pushes down on the top. The forces on the sides are equal and opposite, so they cancel. What is left is an upward resultant force: the upthrust.

Worked example 3: a box under water

A sealed box is 0.50 m tall. Its top and bottom faces each have an area of 0.20 m². It is held in fresh water with its top face 1.0 m below the surface. Find the upthrust on it.

Given: g = 9.8 N/kg, A = 0.20 m², ρ = 1000 kg/m³. The top face is 1.0 m deep, and the bottom face is 1.0 + 0.50 = 1.5 m deep.

Pressure on the top face: p=hρg=1.0×1000×9.8=9800 Pap = h \rho g = 1.0 \times 1000 \times 9.8 = 9800\ \text{Pa}

Pressure on the bottom face: p=1.5×1000×9.8=14 700 Pap = 1.5 \times 1000 \times 9.8 = 14\,700\ \text{Pa}

Pressure difference: 14 700 − 9800 = 4900 Pa

Equation: F=Δp×AF = \Delta p \times A

Substitution: F=4900×0.20F = 4900 \times 0.20

Answer: upthrust = 980 N

Check: the box takes the place of 0.20 × 0.50 = 0.10 m³ of water. That water has a mass of 100 kg and a weight of 980 N. The upthrust equals the weight of the water pushed aside. Push the box deeper and both pressures rise by the same amount, so the upthrust stays the same.

The upthrust and floating simulation lets you explore floating and sinking.

How do manometers and barometers use liquid pressure?

A manometer is a U-tube holding a liquid. Connect one side to a gas supply and leave the other open to the air. If the gas pushes the liquid so that the open side stands 0.15 m higher, the gas pressure is greater than the atmosphere's by 0.15×1000×9.8=14700.15 \times 1000 \times 9.8 = 1470 Pa, using water.

A mercury barometer works the same way. The atmosphere holds up a column of mercury about 0.76 m tall. With mercury's density of about 13 600 kg/m³, that is 0.76×13 600×9.8≈1.0×1050.76 \times 13\,600 \times 9.8 \approx 1.0 \times 10^5 Pa. A water barometer would need a tube more than 10 m tall. For the same reason, a suction pump at the top of a well cannot lift water more than about 10 m.

What does the water-jet experiment show?

Make holes at different heights down the side of a tall plastic bottle or can, stand it in a tray, and keep it topped up with water. Two things happen:

  • Each jet leaves the side at right angles, showing that the pressure pushes sideways as well as down.
  • The jet from the lowest hole leaves the fastest, because the pressure there is greatest.

Be careful how you judge the jets. Where a jet lands depends on two things: how fast it leaves the hole and how far it falls before it lands. With the bottle sitting in the tray, the lowest jet is the fastest but has only a short drop, so a jet from nearer the middle often lands further. Stand the bottle on a block at least as tall as the water is deep, and the lowest jet does land furthest. So use the speed of each jet as it leaves the bottle, not its landing point, as the evidence for pressure.

Change the depth and the liquid in the liquid pressure and depth simulation to test these ideas.

Common mistakes

  • Measuring the depth from the bottom. Measure h down from the liquid surface.
  • Using the length of a sloping pipe. Only the vertical height counts.
  • Adding atmospheric pressure when it is not asked for, or leaving it out when the total is asked for.
  • Saying liquid pressure only acts downwards. At a point, it acts in all directions.
  • Thinking upthrust grows as a fully submerged object sinks deeper. The difference between top and bottom stays the same.
  • Forgetting to convert. Use metres, and change g/cm³ to kg/m³ by multiplying by 1000.

Key points

  • Pressure in a liquid increases with depth: p=hρgp = h\rho g, also written p=ρghp = \rho g h.
  • Between two points, Δp=ρgΔh\Delta p = \rho g \Delta h, where Δh is their vertical separation.
  • Liquids barely compress, so fresh water adds about 9800 Pa for every metre of depth.
  • At any point, liquid pressure acts equally in all directions.
  • Taps higher up get lower pressure, and blood pressure is measured level with the heart.
  • The extra pressure on the bottom of a submerged object causes the upthrust on it.