Skip to content

Alpha, Beta and Gamma Radiation: Properties, Penetration, Uses and Safety

Learn what alpha, beta and gamma radiation are, why alpha ionises most but penetrates least, what absorbs each one, how they behave in fields, where they are used, and how irradiation differs from contamination.

Published · 8 min read

On this page

Unstable nuclei give out three main types of nuclear radiation:

  • An alpha particle (α) is two protons and two neutrons bound together. It is identical to the nucleus of a helium atom.
  • A beta particle (β⁻) is a fast-moving electron. It is created inside the nucleus when a neutron changes into a proton, and is then thrown out.
  • A gamma ray (γ) is high-frequency electromagnetic radiation given out by a nucleus. It has no mass and no charge.

The three behave very differently. Alpha is the most ionising but the least penetrating: a sheet of paper stops it. Beta is in the middle and is stopped by a few millimetres of aluminium. Gamma is the least ionising and the most penetrating. Thick lead or concrete reduces it a lot, but never stops all of it.

What does ionising mean?

An atom is ionised when it gains or loses electrons and so becomes charged. All three types of nuclear radiation can knock electrons out of the atoms they pass. That is why they are called ionising radiation, and why they can harm living cells.

Ionising power and penetration are closely linked. Each time radiation ionises an atom, it loses some energy. Alpha particles are heavy, fairly slow and carry a charge of +2, so they ionise very strongly, knocking electrons off a huge number of atoms along a short path. They leave a dense trail of ions and use up their energy within a few centimetres. Beta particles are lighter, faster and carry a charge of −1, so they ionise less often and travel further. Gamma rays have no charge and pass most atoms without interacting, so they go furthest of all.

How do alpha, beta and gamma compare?

PropertyAlpha (α)Beta (β⁻)Gamma (γ)
What it is2 protons and 2 neutrons (a helium nucleus)A fast electron from the nucleusAn electromagnetic wave
Relative charge+2−10
Relative mass4about 0.00050
Ionising powerStrongModerateWeak
Typical range in airAbout 3 to 7 cmTens of centimetres to a few metresNo fixed range
Absorbed byA sheet of paper, or the outer layer of skinA few millimetres of aluminiumReduced by several centimetres of lead or metres of concrete

The ranges are approximate, because they depend on the energy of the radiation, which differs between isotopes. A gamma beam has no fixed range: it spreads out and is slowly absorbed, so its intensity keeps falling with distance.

What happens to alpha, beta and gamma in electric and magnetic fields?

Electric and magnetic fields push charged particles sideways, but not uncharged radiation.

  • Alpha particles are positive. Between two charged plates, they bend towards the negative plate.
  • Beta particles are negative, so they bend the opposite way, towards the positive plate.
  • Gamma rays have no charge, so they pass straight through.

A magnetic field also bends alpha and beta in opposite directions. In both kinds of field, beta particles are deflected more than alpha particles. In a magnetic field the difference is very large, mainly because beta particles are so much lighter: an alpha particle has more than 7000 times the mass of an electron.

Cambridge IGCSE includes this deflection in its Supplement content. AQA GCSE limits the properties you need to penetration, range in air and ionising power.

How can you tell which radiation a source gives out?

A Geiger–Müller tube and a counter are used. First, the background count rate is measured with no source nearby. Then the source is clamped close to the tube, so the air does not absorb any alpha, and the count rate is measured with different absorbers in between. Subtract the background from every reading. A big drop with paper means alpha. A big drop with aluminium means beta. Whatever still gets through the aluminium is gamma.

Worked example 1: identifying the radiation

In a school lab in Toronto, the background count rate is 24 counts per minute. With the source in position, the counter reads 644 counts per minute with no absorber, 634 behind paper, 204 behind 5 mm of aluminium, and 28 behind 5 cm of lead. Which types of radiation does the source give out?

Equation: corrected reading = measured reading − background

Substitution: 644 − 24 = 620, 634 − 24 = 610, 204 − 24 = 180 and 28 − 24 = 4 counts per minute

Paper: the corrected value falls by only 10. Decay is random, so readings vary by about this much anyway. There is no alpha.

Aluminium: the value falls from 610 to 180. Something is stopped by aluminium but not by paper, so beta is present.

Lead: 180 counts per minute get through the aluminium, and the lead removes almost all of them. Only gamma can pass through 5 mm of aluminium.

Answer: the source gives out beta and gamma radiation.

Worked example 2: how much lead?

Each layer of lead of a certain thickness removes the same fraction of the gamma rays that reach it. Suppose every 1.2 cm of lead halves the gamma count rate from a source. A technician must cut a corrected count rate of 1600 counts per minute down to 100 counts per minute. How thick must the lead be?

Given: starting count rate = 1600 counts per minute, target = 100 counts per minute, halving thickness = 1.2 cm

Number of halvings: 1600 → 800 → 400 → 200 → 100, which is 4 halvings

Equation: thickness of lead = number of halvings × halving thickness

Substitution: thickness = 4 × 1.2

Answer: 4.8 cm of lead. Even then, 100 counts per minute still get through. No thickness brings it to exactly zero.

What are alpha, beta and gamma used for?

The best choice depends on how far the radiation penetrates, and on the half-life of the source.

  • Smoke alarms (alpha). A tiny americium-241 source ionises the air between two metal plates, so a small current flows. Smoke absorbs the alpha particles, the current drops and the alarm sounds. Alpha's short range keeps it inside the alarm.
  • Thickness control (beta). Factories making paper, plastic film or aluminium foil pass the sheet between a beta source and a detector. If fewer beta particles get through, the sheet is too thick, and the rollers adjust. Alpha would be stopped completely, and gamma would barely notice the sheet.
  • Sterilising (gamma). Gamma rays kill bacteria on syringes and dressings already sealed in their packets. Some foods, such as spices, are treated the same way.
  • Medicine (gamma). Tracers with short half-lives are tracked by a camera outside the body. To treat a tumour, gamma beams are aimed at it from several directions, so the tumour gets a large dose and healthy tissue much less. (Today many hospitals use high-energy X-rays from a machine for this instead, but school courses usually describe it with gamma.)

Explore all three types in the alpha, beta and gamma simulation. For half-life, use the radioactive decay simulation.

How dangerous is each type?

Ionising radiation can damage the DNA in cells. Damaged cells may grow out of control and cause cancer. Large doses kill cells directly and can cause radiation sickness and burns.

The most dangerous type depends on where the source is:

  • Outside the body, beta and gamma are the bigger risk, because they can pass through skin and reach organs. Alpha is stopped by the dead outer layer of skin.
  • Inside the body, an alpha source is the most dangerous. If it is breathed in, swallowed or gets into a cut, all of its ionisation happens in a small volume of living tissue.

Radon, a natural gas that seeps into buildings from the ground, is an alpha emitter. Breathing it in for many years raises the risk of lung cancer.

What is the difference between irradiation and contamination?

Irradiation means exposure to radiation from a source outside the object. The object does not become radioactive, and the exposure stops once the source is removed or shielded. A syringe sterilised with gamma rays is safe to use.

Contamination means radioactive atoms have got onto or into something, such as dust on skin or a gas that has been breathed in. Those atoms keep decaying, so the exposure goes on until they are removed or have decayed. Contamination can also spread.

To reduce irradiation, keep your distance, use shielding and spend as little time near the source as possible. To prevent contamination, wear gloves, never eat or drink near sources, and wash your hands afterwards. In school, sources are stored in lead-lined boxes, handled with tongs at arm's length and never pointed at anyone. Radiation workers wear dosimeter badges that record their dose.

Common mistakes

  • Saying lead stops gamma. Thick lead greatly reduces gamma, but some always gets through.
  • Saying alpha is harmless. It is fairly safe outside the body, but inside the body it is the most dangerous type.
  • Saying an irradiated object becomes radioactive. It does not. Contamination means radioactive atoms are actually present.
  • Saying a beta particle comes from the electron shells. It is made in the nucleus, when a neutron turns into a proton.
  • Mixing up ionising power and penetration. The most ionising radiation penetrates least.

Key points

  • Alpha: a helium nucleus, charge +2, strongly ionising, a few centimetres in air, stopped by paper.
  • Beta (β⁻): a fast electron from the nucleus, charge −1, moderately ionising, stopped by a few millimetres of aluminium.
  • Gamma: an electromagnetic wave with no charge or mass, weakly ionising, reduced but never fully stopped by thick lead or concrete.
  • The more strongly a radiation ionises, the less it penetrates.
  • In fields, alpha and beta bend in opposite directions, and gamma does not bend.
  • Irradiation does not make objects radioactive. Contamination means radioactive material is on or in something.