Thermistors and LDRs Explained: Sensor Circuits That Respond to Heat and Light
Learn how the resistance of an NTC thermistor and an LDR changes, how to recognise their symbols, where they are used, and how a potential divider turns a change in resistance into a change in p.d. that can switch a heater, fan or street lamp.
Published · 7 min read
On this page
A thermistor is a resistor whose resistance depends on its temperature. In the usual type, the NTC thermistor, the resistance falls as the temperature rises. A light-dependent resistor (LDR) is a resistor whose resistance falls as the light shining on it gets brighter.
Because their resistance follows their surroundings, both make useful sensors. Connect one to a battery in series with a fixed resistor, and the p.d. across each part changes as the room warms up or the evening gets darker. That changing p.d. can switch on a heater, a fan or a street lamp, with nobody pressing a switch.
How does a thermistor's resistance change with temperature?
NTC stands for negative temperature coefficient. "Negative" means the two quantities move in opposite directions: temperature up, resistance down. This is the opposite of a metal wire or a lamp filament, whose resistance rises as it heats up.
Here are typical values for one common thermistor. Others have different values, but the pattern is the same.
| Temperature | Resistance (approximate) |
|---|---|
| 0 °C | 34 kΩ |
| 25 °C | 10 kΩ |
| 50 °C | 3.6 kΩ |
| 100 °C | 0.7 kΩ |
Plot these values and you get a curve. It drops steeply while the thermistor is cold, then flattens out as it gets hotter.
The symbol is the ordinary resistor rectangle with a slanting line drawn through it. At its lower end, the line bends to run flat for a short distance, a little like a hockey stick.
How does an LDR's resistance change with light?
An LDR has a very high resistance in the dark. As more light falls on it, its resistance drops. For a small LDR, typical values are:
- Darkness: about 1 MΩ (a million ohms) or more
- A dim room: around 10 kΩ
- Bright light: a few hundred ohms or less
These are rough figures, and every LDR is a little different. Its graph of resistance against light intensity is a curve too.
The symbol is the resistor rectangle with two small arrows pointing at it, showing light arriving. Some courses, including AQA, draw it inside a circle.
A quick way to remember both: hotter or brighter means lower resistance.
Where are thermistors and LDRs used?
Thermistors measure or control temperature:
- thermostats in home heating, water heaters and air conditioners
- fridges, freezers and ovens
- engine cooling systems in cars and buses
- digital thermometers
- phone and laptop batteries, so the charger can stop if they overheat
- incubators for hatching eggs on poultry farms in Kenya or Punjab
LDRs respond to light:
- street lamps that switch on at dusk in Karachi, Delhi or Leeds
- solar garden lights and outdoor security lights
- night lights that come on when the room goes dark
How does a sensor circuit work?
A sensor on its own is not enough. If an LDR is connected straight across a battery, the p.d. across it is always the full battery p.d., so nothing useful changes except the current. The trick is to add a fixed resistor in series. This arrangement is called a potential divider.
The same current passes through both parts. Since , the part with the larger resistance takes the larger share of the supply p.d. In fact, the ratio of the two p.d.s equals the ratio of the two resistances:
Now let one resistor be a sensor. When its resistance changes, the share of the p.d. changes. The output, taken across one of the two parts, is used as a signal. It feeds a switching circuit, in practice a transistor or a chip, often with a relay. That circuit lets the small signal switch a much larger current for a heater or lamp.
Which part should the output be across? Think it through one step at a time:
- Lamp on at dusk: as it gets dark, the LDR's resistance rises, so its share of the p.d. rises. Take the output across the LDR.
- Fan on when hot: as it warms, the thermistor's resistance falls, so its share falls and the fixed resistor's share rises. Take the output across the fixed resistor.
Using a variable resistor in place of the fixed one lets you choose the temperature or light level at which the switch happens. A variable potential divider is a single resistor track with a sliding contact. Moving the slider gives any output from zero up to the full supply p.d., as in an old volume knob.
Worked example 1: a thermistor in a greenhouse
A student in Murree builds a sensor for a greenhouse. A thermistor is in series with a 2.0 kΩ fixed resistor across a 9.0 V supply. The thermistor's resistance is 4.0 kΩ on a cold morning and 1.0 kΩ on a warm afternoon. Find the p.d. across each part at both times.
Cold, using the series rules: total resistance Ω, so A
Thermistor: V. Fixed resistor: V
Warm, using the ratio: , so the fixed resistor takes twice the thermistor's share. Splitting 9.0 V in the ratio 1 : 2 gives 3.0 V and 6.0 V.
Answer: cold: 6.0 V across the thermistor and 3.0 V across the fixed resistor. Warm: 3.0 V and 6.0 V. A fan switch connected across the fixed resistor sees its input rise from 3.0 V to 6.0 V as the air warms.
Worked example 2: when does the street lamp switch on?
An LDR is in series with a 10 kΩ fixed resistor across a 12 V supply. The lamp's switch turns on when the p.d. across the LDR reaches 8.0 V. (a) What is the LDR's resistance at that moment? (b) In daylight, the LDR's resistance is 500 Ω. Find the p.d. across it.
(a) The fixed resistor has V. Using : Ω, or 20 kΩ.
(b) Total resistance Ω, so A. Then V.
Answer: the lamp switches on when the LDR reaches 20 kΩ. In daylight, the LDR has only 0.57 V across it, far below 8.0 V, so the lamp stays off.
Our LDR, thermistor and potential divider simulation lets you explore sensor circuits like these. To compare with a component whose resistance goes the other way, open the I–V characteristics simulation, choose Lamp, then tap Take a full set of readings and watch the graph. It bends because the filament's resistance rises as it heats up. That simulation covers a resistor, a lamp and a diode, but not thermistors or LDRs. Our guide to series and parallel circuits has more practice with sharing p.d.
Common mistakes
- Thinking every resistance rises with temperature. Metal wires and filaments do. NTC thermistors do the opposite.
- Confusing an LDR with an LED. An LDR responds to light. An LED gives out light.
- Leaving out the fixed resistor. A sensor connected straight across the supply always has the full supply p.d.
- Choosing the wrong output. Decide which part's share of the p.d. rises when the condition you want happens.
- Turning the ratio upside down. goes with , the p.d. across that same resistor.
- Mixing kΩ and Ω. Convert everything to ohms before using .
Key points
- An NTC thermistor's resistance falls as its temperature rises.
- An LDR's resistance falls as the light intensity rises.
- Thermistors are used in thermostats and temperature sensors. LDRs are used in lights that come on at dusk.
- In a potential divider, two resistors in series share the supply p.d. in proportion to their resistances: .
- A sensor plus a fixed resistor gives a p.d. that changes with temperature or light, which can work a switch.