Skip to content

Sankey Diagrams Explained: How to Read and Draw Them, and Find Efficiency

A Sankey diagram shows where the energy going into a device ends up, with every arrow width drawn to scale. Learn how to read one, draw one on squared paper from a set of values, check it with conservation of energy and work out the efficiency, with three worked examples.

Published · 7 min read

On this page

A Sankey diagram is a picture of an energy transfer. One wide arrow shows the energy going in. It splits into narrower arrows that show where that energy ends up: the useful output and the wasted output. Every arrow's width is drawn to scale, so a wider arrow carries more energy.

Energy cannot be created or destroyed, so the output arrows always add up to the input arrow. Because the widths are to scale, the diagram gives you the efficiency directly. It is the useful arrow's width as a fraction of the input arrow's width.

The diagrams are named after Matthew Sankey, an engineer who drew one in the late 1890s to show where the energy in a steam engine went.

What does each part of a Sankey diagram show?

  • The input arrow, on the left, shows the total energy supplied. Its label says where the energy comes from or how it arrives, such as "chemical store of the fuel" or "energy transferred electrically".
  • The useful arrow usually carries straight on to the right. It shows the energy that does the job you want.
  • The wasted arrows usually bend away, often downwards. Most wasted energy ends up heating the device and its surroundings. Some leaves as sound.
  • Each arrow has a label saying what the energy is and how much there is.

What counts as useful depends on the job. For a lamp, the light is useful and the heating is wasted. For an electric heater, the heating is useful, and any light from its glowing wires is wasted.

How do you read a Sankey diagram?

  1. Find the scale: divide the input energy by the width of the input arrow.
  2. Multiply each arrow's width by the scale to find its energy.
  3. Check that the outputs add up to the input.
  4. Work out the efficiency.
efficiency=useful output energytotal input energy\text{efficiency} = \frac{\text{useful output energy}}{\text{total input energy}}

Multiply by 100 for a percentage. The result is always 1 (100%) or less, because the useful arrow is never wider than the input arrow.

Worked example 1: a food blender

A Sankey diagram for a blender is drawn on squared paper. The input arrow spans 20 squares and is labelled 1000 J. The useful arrow, for the kinetic store of the blades and food, is 13 squares wide. The two wasted arrows are 6 squares wide (heating) and 1 square wide (sound). Find the energy in each arrow and the efficiency.

Scale: 1000÷20=501000 \div 20 = 50 J per square

Useful: 13×50=65013 \times 50 = 650 J

Heating: 6×50=3006 \times 50 = 300 J

Sound: 1×50=501 \times 50 = 50 J

Check: 650+300+50=1000650 + 300 + 50 = 1000 J, the same as the input

Efficiency: 6501000=0.65\dfrac{650}{1000} = 0.65

Answer: the blender is 0.65, or 65%, efficient. The widths alone give the same result: 13÷20=0.6513 \div 20 = 0.65. If all you need is the efficiency, you can skip the scale, because it cancels out.

How do you draw a Sankey diagram to scale?

  1. Add up the outputs and check that they equal the input.
  2. Choose a scale that lets the input arrow fit on the page, such as 1 mm for 10 kJ, or one square for 20 J.
  3. Divide each energy by the scale to get each arrow's width.
  4. Draw the input arrow. Split it, keep the useful arrow going straight on, and bend each wasted arrow away.
  5. Label every arrow with what it is and its value.

Worked example 2: a car engine

As a car speeds up along a road in Lagos, its engine transfers 800 kJ from the chemical store of the fuel. 200 kJ goes to the kinetic store of the car. 580 kJ heats the engine, the exhaust gases and the surroundings, and 20 kJ is carried away by sound. These are example values. Draw the diagram with a scale of 1 mm for 10 kJ, and find the efficiency.

Check: 200+580+20=800200 + 580 + 20 = 800 kJ

Input arrow: 800÷10=80800 \div 10 = 80 mm wide

Useful arrow: 200÷10=20200 \div 10 = 20 mm wide

Heating arrow: 580÷10=58580 \div 10 = 58 mm wide

Sound arrow: 20÷10=220 \div 10 = 2 mm wide

Efficiency: 200800=0.25\dfrac{200}{800} = 0.25

Answer: the arrows are 80 mm, 20 mm, 58 mm and 2 mm wide, and 20+58+2=8020 + 58 + 2 = 80 mm, so the diagram balances. The engine is 25% efficient. Petrol car engines often manage only about a quarter, so the heating arrow is by far the widest.

If an arrow would be too thin to draw clearly, like the 2 mm sound arrow, still draw it as a narrow arrow and label its value.

Can a Sankey diagram show power instead of energy?

Yes. Each arrow can show the energy transferred each second, which is the power in watts. If the device runs steadily, every second looks the same. The power diagram then has exactly the same shape as one for the whole run, and gives the same efficiency.

Worked example 3: a phone charger

A phone charger in Mumbai takes in 20 W. Its Sankey diagram shows a heating arrow of 2.4 W, and one other arrow, into the chemical store of the phone's battery, whose label is missing. Work out the missing value and the charger's efficiency.

Energy is conserved, so: 20−2.4=17.620 - 2.4 = 17.6 W

Efficiency: 17.620=0.88\dfrac{17.6}{20} = 0.88

Answer: 17.6 W reaches the battery, so the charger is 88% efficient.

What does a diagram with several stages show?

Some diagrams follow energy through a chain of devices. In a power station, for example, the energy from the fuel passes through a boiler, then a turbine, then a generator. Each stage has its own wasted arrow. The useful arrow from one stage becomes the input to the next. So the overall efficiency is lower than the efficiency of any one stage. It is the final useful output divided by the very first input. For more on chains of devices, see our guide to calculating efficiency.

How can you explore Sankey diagrams?

In our power and efficiency simulation, choose Crane with a 40% efficient motor from the Set-up menu. Below the stage, a Sankey diagram shows the motor's input split into a useful arrow and a wasted arrow, with widths to scale. Switch Show between Energy (whole lift) and Power (each second): the shape stays the same. Then pick Crane with an 80% efficient motor and watch the wasted arrow shrink. You can also follow energy between stores in the energy stores and transfers simulation.

Common mistakes

  • Measuring the length of an arrow. Only the width stands for the energy.
  • Output arrows that do not add up to the input. Energy is conserved, so check the total every time.
  • Dividing the wasted energy by the input. The efficiency uses the useful output.
  • Getting an efficiency above 100%. That means the numbers are upside down or misread.
  • Mixing J and kJ. Use one unit for every arrow.
  • Saying wasted energy is destroyed. It still exists. It has spread out into the surroundings, where it is much less useful.

Key points

  • A Sankey diagram shows energy in, useful energy out and wasted energy out, with every width to scale.
  • The output widths always add up to the input width, because energy is conserved.
  • Efficiency = useful output ÷ total input, which is also useful width ÷ input width.
  • To draw one, check the total, choose a scale, work out each width, then draw and label.
  • A diagram can show energy for a whole task or power each second. For a steady device, both have the same shape.