Skip to content

Resolving Forces into Components: F cos θ, F sin θ and Forces on a Slope

Learn what resolving a force means, which component gets cos and which gets sin, what to do when the angle is measured from the vertical, how to find the pull of gravity down a slope, how to handle forces in other quadrants, and how to resolve with a scale drawing.

Published · 8 min read

On this page

To resolve a force means to replace it with two forces at right angles to each other that, together, have exactly the same effect. These two forces are its components. If the force F makes an angle θ with the horizontal, then:

Fx=Fcos⁡θFy=Fsin⁡θF_x = F\cos\theta \qquad F_y = F\sin\theta

Here FxF_x is the horizontal component and FyF_y the vertical one. The rule to remember is simple. The component next to the angle gets cos. The component opposite the angle gets sin. So if the angle is measured from the vertical instead, the two swap over.

Why split a force into two?

A force at an angle does two jobs at once. Drag a box with a sloping rope, and part of your pull moves it forwards while the other part lifts some of its weight off the floor. Splitting the force lets you deal with each direction on its own, using simple sums along a straight line. It also tells you how hard gravity drags a parked car down a hill.

How do you find F cos θ and F sin θ?

Draw the force as an arrow from a point. From its tip, draw a line straight down to the horizontal. This makes a right-angled triangle, with the force F as its longest side, the hypotenuse.

  • The horizontal side lies next to θ. Since cos⁡θ=Fx÷F\cos\theta = F_x \div F, the horizontal component is Fx=Fcos⁡θF_x = F\cos\theta.
  • The vertical side lies opposite θ. Since sin⁡θ=Fy÷F\sin\theta = F_y \div F, the vertical component is Fy=Fsin⁡θF_y = F\sin\theta.

Two quick checks catch most mistakes. First, at 0° the whole force is horizontal, at 90° it is all vertical, and at 45° the two components are equal, each about 0.71F. Second, the components rebuild the force by Pythagoras: Fx2+Fy2=F2F_x^2 + F_y^2 = F^2.

Worked example 1: dragging a box of books

In a school in Accra, a student drags a heavy box of books across the floor with a rope. The rope pulls with 80 N at 35° above the floor. Work out the forward and upward components of the pull.

Given: F = 80 N, θ = 35° above the horizontal

Horizontal: Fx=Fcos⁡θ=80×cos⁡35∘=80×0.819=65.5F_x = F\cos\theta = 80 \times \cos 35^\circ = 80 \times 0.819 = 65.5 N

Vertical: Fy=Fsin⁡θ=80×sin⁡35∘=80×0.574=45.9F_y = F\sin\theta = 80 \times \sin 35^\circ = 80 \times 0.574 = 45.9 N

Answer: about 66 N forwards and 46 N upwards (2 significant figures)

Check: 65.52+45.92=80.0\sqrt{65.5^2 + 45.9^2} = 80.0 N, the size of the original force.

Which angle should you use?

Questions do not always give the angle above the horizontal. Whatever the angle, the same rule holds: cos goes with the component that touches the angle.

If θ is measured from the vertical, the vertical component is Fcos⁡θF\cos\theta and the horizontal one is Fsin⁡θF\sin\theta. If you prefer, first work out the angle with the horizontal, which is 90∘−θ90^\circ - \theta, and then use the usual pair.

Worked example 2: a guy rope on a tent

On a trek near Skardu, a tent's guy rope pulls on its peg with 150 N, at 40° to the vertical. Find the vertical and horizontal components of the pull on the peg.

Which angle? The 40° is measured from the vertical, so the vertical component touches the angle and gets cos.

Vertical: 150×cos⁡40∘=150×0.766=115150 \times \cos 40^\circ = 150 \times 0.766 = 115 N, trying to lift the peg out of the ground

Horizontal: 150×sin⁡40∘=150×0.643=96.4150 \times \sin 40^\circ = 150 \times 0.643 = 96.4 N

Check by the other route: the angle with the horizontal is 90° − 40° = 50°, and 150×cos⁡50∘=96.4150 \times \cos 50^\circ = 96.4 N. Both routes agree.

How do you resolve weight on a slope?

On a slope, horizontal and vertical are not the useful directions. Instead, resolve along the slope and at right angles to it.

The weight, W = mg, acts straight down. Tilt the ground by an angle θ, and the line at right angles to the slope tilts by the same angle. So the angle between the weight and that line is θ. The component at right angles to the slope touches the angle, so it gets cos:

down the slope: mgsin⁡θinto the slope: mgcos⁡θ\text{down the slope: } mg\sin\theta \qquad \text{into the slope: } mg\cos\theta

Check the extremes. On flat ground, sin 0° = 0, so nothing pulls the object along. On a vertical cliff, sin 90° = 1, so the whole weight acts down the "slope". Steeper slopes pull harder.

The ground pushes back on the component into the slope, so the normal contact force on a slope is less than the full weight. The component down the slope must be balanced by friction, or the object slides.

Worked example 3: a car parked on a hill

A car of mass 1200 kg is parked on a hillside street in Wellington, New Zealand. The street slopes at 10° to the horizontal. Use g = 9.8 N/kg.

(a) Calculate the component of the car's weight down the slope. (b) Calculate the component into the road. (c) How large a friction force must the brakes and tyres provide to hold the car still?

Weight: W = mg = 1200 × 9.8 = 11 760 N

(a) Wsin⁡10∘=11 760×0.1736=2040W\sin 10^\circ = 11\,760 \times 0.1736 = 2040 N, about 2.0 kN

(b) Wcos⁡10∘=11 760×0.985=11 600W\cos 10^\circ = 11\,760 \times 0.985 = 11\,600 N (3 significant figures)

(c) The car is still, so the forces along the slope balance. Friction must push up the slope with about 2.0 kN.

With g = 10 N/kg, as Punjab books use, part (a) gives about 2.1 kN instead.

What if the force points into another quadrant?

Many books, and our simulation, measure every direction anticlockwise from the positive x-axis, so 0° is to the right and 90° is straight up. A component that points left or down is then negative.

There are two ways to get the signs right:

  1. Type the full angle into the calculator. Cos and sin then give the signs for you.
  2. Find the angle between the force and the nearest part of the x-axis. Work out the sizes of the components with that angle, then add the signs from a sketch.
Direction of the forceSign of the x-componentSign of the y-component
Between 0° and 90° (up and right)++
Between 90° and 180° (up and left)−+
Between 180° and 270° (down and left)−−
Between 270° and 360° (down and right)+−

Worked example 4: a force at 150°

A 20 N force acts at 150°, measured anticlockwise from the positive x-axis. Find its components.

Method 1: Fx=20×cos⁡150∘=20×(−0.866)=−17.3F_x = 20 \times \cos 150^\circ = 20 \times (-0.866) = -17.3 N and Fy=20×sin⁡150∘=20×0.500=10.0F_y = 20 \times \sin 150^\circ = 20 \times 0.500 = 10.0 N

Method 2: the force makes 180° − 150° = 30° with the negative x-axis. The sizes are 20cos⁡30∘=17.320 \cos 30^\circ = 17.3 N and 20sin⁡30∘=10.020 \sin 30^\circ = 10.0 N. A sketch shows the force pointing up and to the left, so the x-component is negative.

Answer: Fx=−17.3F_x = -17.3 N (17.3 N to the left) and Fy=+10.0F_y = +10.0 N (10.0 N upwards). Both methods agree.

How do you resolve a force with a scale drawing?

Some courses ask for a drawing instead of trigonometry. Here is the rope pull from worked example 1, resolved by drawing:

  1. Pick a scale. With 1 cm standing for 10 N, the 80 N force becomes an 8.0 cm arrow.
  2. Draw a horizontal line. With a protractor, draw the arrow at 35° above it.
  3. From the tip of the arrow, draw a line down to the horizontal line, at right angles to it. A set square helps.
  4. Measure the two sides of the triangle: about 6.6 cm along the bottom and 4.6 cm up the side.
  5. Convert with the scale: about 66 N horizontally and 46 N vertically.

That matches the calculation. A drawing is only as good as your measuring, so draw big and measure carefully.

Practise in the adding and resolving vectors simulation. Choose Resolve under Mode, and it opens with 10 N at 30°. Press Components to show the dashed components, and the working lines fill in Fx=Fcos⁡θF_x = F\cos\theta and Fy=Fsin⁡θF_y = F\sin\theta for you. Then pick the 120° force from the Example list: its x-component card turns negative. Turn on Scale drawing to measure the components on a grid, or press Reverse to build a force from its two components.

Common mistakes

  • Mixing up sin and cos. The component beside the angle takes cos, wherever the angle is measured from.
  • Leaving the calculator in radians. In radians mode, cos 35 gives −0.90 instead of 0.82. Check for the D or DEG sign on the screen.
  • Adding the components to get the force. 65.5 N and 45.9 N combine by Pythagoras to 80 N, not 111 N.
  • Using mgcos⁡θmg\cos\theta down a slope. The component down the slope is mgsin⁡θmg\sin\theta. It must be zero on flat ground.
  • Dropping a minus sign. A component pointing left or down is negative when right and up are positive.

Key points

  • Resolving replaces one force with two components at right angles that have the same combined effect.
  • For an angle θ above the horizontal, Fx=Fcos⁡θF_x = F\cos\theta and Fy=Fsin⁡θF_y = F\sin\theta. Cos goes with the side next to the angle.
  • If the angle is measured from the vertical, the vertical component is Fcos⁡θF\cos\theta.
  • On a slope at angle θ, the weight has a component mgsin⁡θmg\sin\theta down the slope and mgcos⁡θmg\cos\theta into it.
  • With angles measured anticlockwise from +x, components pointing left or down are negative.