Magnetisation and Demagnetisation: How to Make a Magnet and How to Destroy One
Learn the single-touch and double-touch stroking methods, how a solenoid and a direct current make a magnet, how to predict the poles each time, and how a.c., heating and hammering destroy magnetism. Includes soft iron against steel and a simple domain model.
Published · 8 min read
On this page
To magnetise a piece of steel means to turn it into a permanent magnet. There are two main ways. You can stroke it with a permanent magnet, or you can put it inside a solenoid (a long coil of wire) and pass a direct current through the coil.
To demagnetise a magnet means to destroy its magnetism. You can place it in a solenoid carrying alternating current and pull it out slowly, heat it strongly, or hammer it while it lies east–west.
Which materials can you magnetise?
Only magnetic materials can be magnetised: iron, steel, nickel, cobalt and some alloys that contain them.
- Soft iron magnetises easily but keeps almost nothing afterwards. It suits a temporary magnet, such as an electromagnet's core, which must let go when the current stops.
- Steel is harder to magnetise, but then it stays magnetised. It suits a permanent magnet, such as a compass needle.
Iron near a magnet becomes a magnet too, without any stroking. This is induced magnetism. It always attracts, and in soft iron it fades almost as soon as the magnet is moved away.
What happens inside a magnet?
Picture a magnetic material as millions of tiny regions, called domains, each acting like a very small magnet. In an unmagnetised bar they point every which way, so their effects cancel. In a magnetised bar most of them point the same way, so their effects add up and the bar has an N pole and an S pole.
Magnetising lines the domains up. Demagnetising scrambles them again. Soft iron's domains turn easily and soon fall back into disorder. Steel's domains resist turning, but once turned they stay put.
How do you magnetise a bar by stroking?
Rest the steel bar on a flat bench.
Single-touch method
- Place one pole of a strong magnet, say the N pole, on one end of the bar.
- Slide it along the whole bar to the other end.
- Lift the magnet high above the bar and carry it back to the start. Keeping it close on the way back would undo some of the work.
- Repeat many times, always in the same direction.
Double-touch method
- Take two magnets. Stand the N pole of one and the S pole of the other side by side at the middle of the bar.
- Slide them apart at the same time, each towards a different end.
- Lift both, return them to the middle and repeat.
The double-touch method usually gives a stronger magnet in fewer strokes.
To predict the poles, remember: the last end touched takes the opposite pole. Wherever a stroking pole leaves the bar, that end becomes the other kind.
Worked example 1: predicting the poles after stroking
(a) A student in Faisalabad strokes a steel bar XY from X to Y, using the S pole of a magnet. (b) A second bar PQ is stroked by the double-touch method: an N pole moves towards end P while an S pole moves towards end Q. Name the poles of each bar.
(a) The S pole leaves the bar at Y, so Y becomes an N pole. X becomes an S pole.
(b) The N pole leaves at P, so P becomes S. The S pole leaves at Q, so Q becomes N.
Check: bring each end near the N end of a compass needle. An end that repels it is an N pole. Only repulsion proves anything, because the needle would also attract an unmagnetised bar.
How do you magnetise a bar with a solenoid?
- Wind a long coil of a few hundred turns, using insulated copper wire so that the current cannot jump from one turn to the next.
- Put the steel bar inside.
- Connect the coil to a d.c. supply, switch on for a moment, then switch off.
- Take out the bar. It is now a permanent magnet.
A larger current or more turns gives a stronger field, which lines up more of the domains. An a.c. supply would not work, because its field keeps reversing.
The right-hand grip rule tells you which end is N. Wrap your right hand round the coil so that your fingers follow the conventional current through the turns, from positive to negative. Your thumb points along the bar to its N end.
Or view the coil end-on. If the current circles anticlockwise as you look, the end facing you is N. If it circles clockwise, that end is S. A handy memory aid: S is the same way as a clock.
Worked example 2: poles from a solenoid
A steel bar lies in a solenoid. Looking at the coil from end K, a student sees the current flowing clockwise. (a) Which pole forms at K? (b) What changes if the student swaps the supply's connections?
(a) Clockwise, as seen from K, means K is an S pole. The far end becomes N.
(b) The current now flows anticlockwise as seen from K, so K becomes N and the far end S.
Can the Earth's field magnetise steel?
Yes, but only weakly. Point a steel rod north–south and give it a series of sharp hammer blows. The shocks loosen the domains, and the Earth's field, weak as it is, tips some of them to face its own way. After a while the rod is a feeble magnet. Its N pole is the end that faced north.
How do you demagnetise a magnet?
1. Alternating current in a solenoid. Put the magnet inside a solenoid connected to an a.c. supply and switch on. Pull the magnet slowly out of the coil and carry it well away, with its length pointing east–west. Only then switch off. The field flips direction many times a second, and it weakens as the magnet moves away. The domains are pushed one way, then the other, a little less each time, until they are left pointing at random.
A second version keeps the magnet inside and turns the a.c. down slowly to zero. Switching off suddenly, with the magnet still inside, can leave it magnetised: the last strong swing of the field is not followed by weaker ones.
2. Heating. Heat the magnet strongly. Its particles vibrate so violently that the domains lose their order. Above a certain temperature the magnetism vanishes completely. For pure iron this is about 770 °C (beyond school courses).
3. Hammering. Strike the magnet hard, again and again, or drop it repeatedly. The jolts knock the domains out of line. Keep it lying east–west while you do this, so that the Earth's field does not act along its length. If the magnet pointed north–south, the Earth's field would line up some of the loosened domains again and leave a weak magnet, as in the section above. (This east–west detail, here and in method 1, goes beyond the Punjab book.)
You can magnetise steel on screen in the magnetic field around a wire and solenoid simulation. Choose Solenoid and pick Steel under Core. At the starting 200 turns and 2 A, the Core card shows the steel holding about a quarter of the most it can keep. Drag Turns up to 400 and press More I until the current reaches 5 A, and the figure climbs close to 100%. Next, press Switch to stop the current, press Reverse, and press Switch twice: on, then off. The N pole card now names the other end, because the reversed d.c. magnetised the steel the other way. Finally, press Demagnetise and the card reads None. The bar magnet field simulation shows the field of a finished magnet.
Common mistakes
- Stroking back and forth. Every stroke must go the same way, with the magnet lifted well clear on the return.
- Getting the stroked poles the wrong way round. The end where the stroke finishes takes the pole opposite to the stroking pole.
- Using a.c. to magnetise. A steady direct current is needed. Alternating current demagnetises.
- Switching off the a.c. with the magnet still inside the coil. Withdraw the magnet first.
- Hammering a magnet that lies north–south when you want to demagnetise it. Lay it east–west.
Key points
- Magnetising lines up a material's domains. Demagnetising scrambles them.
- Steel keeps its magnetism, so it is used for permanent magnets. Soft iron is used for temporary magnets.
- Stroking: the end where a stroke finishes takes the pole opposite to the stroking pole.
- In a solenoid with d.c., the right-hand grip rule gives the N end. Clockwise current, seen from an end, makes that end S.
- Demagnetise with a.c. that fades away, strong heating, or hammering with the magnet lying east–west.