How to Read a Vernier Calliper and a Micrometer Screw Gauge, with Zero Errors
A step-by-step method for reading vernier callipers and a micrometer screw gauge, where each least count comes from, how to spot and correct zero errors in both signed and Punjab-style wording, and six practice readings.
Published · 8 min read
On this page
Both instruments are read the same way: a main scale gives the reading roughly, and a second scale adds a fine correction.
- Vernier calliper (spelt caliper in the US): reading = main scale reading + (vernier line that lines up × 0.01 cm). It reads to 0.1 mm.
- Micrometer screw gauge: reading = sleeve reading + (thimble division on the datum line × 0.01 mm). It reads to 0.01 mm.
Before you measure anything, close the empty jaws and check that the instrument reads zero. If it does not, it has a zero error, and you correct every reading by the same amount. With the signed convention:
The rest of this guide shows where the numbers come from, then works through six readings.
Where does the least count of a vernier calliper come from?
The least count is the smallest change in length an instrument can show. A metre rule has a least count of 1 mm. A vernier does ten times better with a clever trick.
The sliding vernier scale has 10 divisions, but they span only 9 mm of the main scale. So each vernier division measures 0.9 mm, which falls short of one main-scale division by 0.1 mm:
When the jaws open by an extra 0.1 mm, the next vernier line along slides into line with a main-scale mark. So the number of the line that matches tells you how many tenths of a millimetre to add.
Not every calliper is built like this. Some have 20 or 50 vernier divisions, giving least counts of 0.05 mm or 0.02 mm, so always work out the least count of the instrument in your hands first. This guide uses the common school type, which reads to 0.1 mm.
How do you take a vernier reading?
- Close the jaws gently on the object. Do not squeeze it.
- Look at the zero of the vernier scale. Note the last main-scale mark to its left. That is the main scale reading.
- Run your eye along the vernier and find the one line that sits exactly in line with a mark on the main scale. Note its number, n.
- Reading = main scale reading + n × 0.01 cm.
Write the answer to two decimal places in centimetres, because that is the least count. If line 0 matches, write 4.30 cm, not 4.3 cm.
Worked reading 1: a test tube
The vernier zero has just passed 1.6 cm on the main scale. Line 8 of the vernier lines up. There is no zero error. Find the outside diameter of the test tube.
Given: main scale reading = 1.6 cm, n = 8, least count = 0.01 cm
Equation: reading = main scale reading + n × least count
Substitution: reading = 1.6 + 8 × 0.01
Answer: diameter = 1.68 cm (16.8 mm)
How do you find and correct a vernier zero error?
Close the empty jaws and look at where the vernier zero sits.
- Right of the main-scale zero: the calliper already shows a small positive length, so every reading is too big. If line n lines up, the zero error is +n × 0.01 cm. This is a positive zero error.
- Left of the main-scale zero: the calliper reads too little. If line n lines up, the vernier zero is (10 − n) least counts short of 0, so the zero error is −(10 − n) × 0.01 cm. This is a negative zero error.
Then use corrected reading = observed reading − zero error. Subtracting a negative number adds it, so a negative zero error makes the final answer bigger.
Worked reading 2: a cricket ball, positive zero error
Closed with nothing in it, this calliper shows its vernier zero a little to the right of 0 on the main scale, with line 3 lined up. On a cricket ball, the main scale reads 7.1 cm and line 9 lines up. Find the ball's diameter.
Zero error: +3 × 0.01 = +0.03 cm (Punjab wording: 0.03 cm, subtract)
Observed reading: 7.1 + 9 × 0.01 = 7.19 cm
Equation: corrected reading = observed reading − zero error
Substitution: 7.19 − (+0.03)
Answer: diameter = 7.16 cm
Worked reading 3: inside a pipe, negative zero error
A second calliper, when closed, has its vernier zero slightly left of 0 on the main scale, and line 6 is lined up. Its inside jaws are opened in a plastic pipe. The main scale reads 2.0 cm and line 5 lines up. Find the inner diameter.
Zero error: −(10 − 6) × 0.01 = −0.04 cm (Punjab wording: 0.04 cm, add)
Observed reading: 2.0 + 5 × 0.01 = 2.05 cm
Substitution: 2.05 − (−0.04)
Answer: inner diameter = 2.09 cm
In the vernier callipers simulation, you can add a positive or negative zero error, check the zero with the jaws closed, then try Practice mode, which picks a random object for you to measure.
How does a micrometer screw gauge reach 0.01 mm?
A micrometer turns a fine screw. One full turn of the thimble moves the spindle forward by one pitch, usually 0.5 mm. The thimble edge carries 50 divisions, so one division moves the spindle 1/50 of the pitch:
To read it:
- Close the spindle onto the object using the ratchet, and stop when it clicks. This stops you crushing soft objects and gives the same grip every time.
- Read the sleeve. Usually, whole millimetres are marked above the datum line and half millimetres below it. Note the last mark that the thimble edge leaves showing.
- Read the thimble division that lies on the datum line. Multiply by 0.01 mm and add.
The Punjab book calls the datum line the "horizontal line", the sleeve scale the "main scale" and the thimble scale the "circular scale".
Worked reading 4: a steel nail, watch the half mark
The sleeve shows the 2 mm mark, plus a half-millimetre mark below the line. Thimble division 18 is on the datum line. There is no zero error. Find the nail's diameter.
Given: sleeve reading = 2.5 mm, division = 18, least count = 0.01 mm
Equation: reading = sleeve reading + division × least count
Substitution: reading = 2.5 + 18 × 0.01
Answer: diameter = 2.68 mm
Miss the half mark and you would write 2.18 mm, which is 0.5 mm too small.
How do you correct a micrometer zero error?
Wind the spindle onto the anvil with nothing between them, using the ratchet, and see where the thimble's zero stops.
- Zero below the datum line: the gauge reads too much. If division k is on the line, the zero error is +k × 0.01 mm.
- Zero above the datum line: the gauge has turned past zero and reads too little. If division k is on the line, the zero error is −(50 − k) × 0.01 mm.
Correct it in the same way: corrected reading = observed reading − zero error. In Punjab wording, subtract the size when the zero is below the line, and add it when the zero is above.
Worked reading 5: copper wire, positive zero error
Closed, the gauge has its zero below the datum line, with division 3 on the line. On a copper wire, the sleeve shows 1.0 mm (no half mark) and division 41 is on the line.
Zero error: +3 × 0.01 = +0.03 mm
Observed reading: 1.0 + 41 × 0.01 = 1.41 mm
Answer: corrected diameter = 1.41 − 0.03 = 1.38 mm
Worked reading 6: a stack of paper, negative zero error
Another gauge, closed, has its zero above the datum line, with division 48 on the line. A student squeezes 50 sheets of printer paper together. The sleeve shows 5.0 mm with no half mark, and division 6 is on the line. Find the thickness of one sheet.
Zero error: −(50 − 48) × 0.01 = −0.02 mm
Observed reading: 5.0 + 6 × 0.01 = 5.06 mm
Corrected stack: 5.06 − (−0.02) = 5.08 mm
Answer: one sheet = 5.08 ÷ 50 = 0.102 mm (3 significant figures)
Measuring many sheets and dividing spreads the uncertainty of one reading over all 50 sheets. Cambridge IGCSE uses the same idea when it asks you to measure multiples of a small distance.
Practise reading the sleeve and thimble, with or without a zero error, in the micrometer screw gauge simulation.
Common mistakes
- Reading the main scale at the matching line. Read it at the vernier zero (or the thimble edge), then add the fine part.
- Missing the half-millimetre mark on a micrometer sleeve.
- Using 0.1 mm per thimble division. Each one is 0.01 mm.
- Adding a positive zero error. It makes readings too big, so it must come off.
- Using n instead of (10 − n) or (50 − k) when the zero is on the "wrong" side.
- Dropping the final zero. Write 3.40 cm, not 3.4 cm, to show the precision.
Key points
- Vernier: 10 divisions span 9 mm, so the least count is 0.1 mm. Reading = main scale reading + n × 0.01 cm.
- Micrometer: least count = 0.5 mm ÷ 50 = 0.01 mm. Reading = sleeve reading + division × 0.01 mm.
- Always check the zero with the jaws closed before measuring.
- Signed convention: corrected reading = observed reading − zero error.
- Punjab wording: zero on the right (vernier) or below the line (micrometer), subtract; on the left or above the line, add.
- Measure many thin objects together and divide to get a more precise value for one.