Skip to content

Converging Lens Ray Diagrams: How to Draw Them for Every Object Position

Draw converging lens ray diagrams with three simple rays, describe each image as real or virtual, upright or inverted, and magnified or diminished, and use magnification = image height ÷ object height.

Published · 8 min read

On this page

A converging lens, also called a convex lens, is thicker in the middle than at the edges. Rays of light that arrive parallel to its axis are refracted so that they meet at one point, the principal focus, F. The distance from the centre of the lens to F is the focal length, f.

To find the image a lens makes, you draw a ray diagram. Two rays from the top of the object are enough. If they cross on the far side of the lens, a real image forms there. If they spread apart, you trace them backwards to find a virtual image.

The kind of image depends on where the object is. For an object outside F, moving it closer to the lens makes the image bigger and further away. Once the object is inside F, the lens works as a magnifying glass.

What words describe an image?

Every image is described with three pairs of words:

  • Real or virtual. A real image forms where light rays actually meet, so you can catch it on a screen. A virtual image is the place the rays only appear to come from. You see it by looking through the lens, but it cannot appear on a screen.
  • Upright or inverted. Is the image the same way up as the object, or upside down?
  • Magnified or diminished. Is it bigger or smaller than the object? If it is the same size, say so. Some courses say "enlarged" instead of "magnified".

How do you draw a ray diagram for a converging lens?

Draw a horizontal line through the centre of the lens. This is the principal axis. Mark F on both sides of the lens, a distance f from the centre, and mark 2F at twice that distance. Draw the lens as a thin vertical line. Many exam papers draw a converging lens as a line with an outward-pointing arrowhead at each end.

Stand the object on the axis as an upright arrow. Then, with a ruler, draw these rays from the tip of the arrow:

  1. A ray parallel to the axis. After the lens, it passes through F on the far side.
  2. A ray through the centre of the lens. It carries straight on without bending.
  3. A ray through F on the near side. After the lens, it travels parallel to the axis.

Any two of these rays fix the image. The third is a useful check. For a thin lens, show the bending at the centre line of the lens, not at its curved surfaces. Put arrowheads on every ray to show which way the light travels.

What image forms for each object position?

Object beyond 2F

The rays meet between F and 2F on the other side. The image is real, inverted and diminished. A camera works like this: a distant scene forms a small, sharp image on the sensor. The lens in your eye does the same, forming a small, upside-down image on the retina.

Object at 2F

The image forms at 2F on the other side. It is real, inverted and the same size as the object.

Object between F and 2F

The image forms beyond 2F on the other side. It is real, inverted and magnified. A projector uses this arrangement to throw a large picture onto a screen. In an old slide projector, the slide went in upside down, so the picture on the screen came out the right way up.

Object at F

The rays leave the lens parallel to each other. They never meet, so no image forms. Some books say the image is "at infinity". A lamp at the focus of a lens gives a strong parallel beam, which is how a lighthouse throws its light far out to sea.

Object inside F

Now the rays are still spreading out after the lens, so they never meet. Extend them backwards with dashed lines. They seem to come from a point on the same side of the lens as the object. The image is virtual, upright and magnified. This is a magnifying glass: you hold the lens within one focal length of the object and look through it.

Object positionImage positionType of imageExample
Beyond 2FBetween F and 2F, other sideReal, inverted, diminishedCamera, eye
At 2FAt 2F, other sideReal, inverted, same sizeThe dividing case
Between F and 2FBeyond 2F, other sideReal, inverted, magnifiedProjector
At FNo image (parallel rays)NoneLighthouse beam
Inside FSame side as the objectVirtual, upright, magnifiedMagnifying glass

Explore these cases in the lenses and ray diagrams simulation.

How do you calculate magnification?

magnification=image heightobject height\text{magnification} = \frac{\text{image height}}{\text{object height}}

Magnification is a ratio of two lengths, so it has no unit. Measure both heights in the same unit, such as millimetres or centimetres. A value above 1 means the image is magnified. A value below 1 means it is diminished.

Worked example 1: a classroom projector

A projector in a school in Lahore forms an image 1.8 m tall from a picture 2.4 cm tall inside the projector. Find the magnification.

Given: image height = 1.8 m = 180 cm, object height = 2.4 cm

Equation: magnification = image height ÷ object height

Substitution: magnification = 1802.4\dfrac{180}{2.4}

Answer: magnification = 75 (no unit)

If you forgot to change 1.8 m into centimetres, you would get 0.75, which wrongly suggests a diminished image.

Worked example 2: a jeweller's lens

A jeweller in Jaipur looks at a mark 1.5 mm tall on a ring through a lens that gives a magnification of 3.0. How tall does the mark appear, and what kind of image is it?

Given: object height = 1.5 mm, magnification = 3.0

Equation: image height = magnification × object height

Substitution: image height = 3.0 × 1.5

Answer: image height = 4.5 mm. A lens used like this holds the object inside F, so the image is virtual, upright and magnified.

Worked example 3: a scale drawing

An object 2.0 cm tall stands 15 cm from a converging lens of focal length 10 cm. Find the position, size and type of the image with a scale drawing.

  1. Choose a scale. Let 1 cm on the paper represent 2 cm. Mark F at 5 cm and 2F at 10 cm on each side of the lens. Draw the object 1.0 cm tall, 7.5 cm from the lens.
  2. Ray 1. From the tip of the object, draw a ray parallel to the axis that bends through F on the far side.
  3. Ray 2. Draw a ray from the tip straight through the centre of the lens.
  4. Read the drawing. The rays cross 15 cm from the lens, 2.0 cm below the axis.
  5. Scale up. Image distance = 15 × 2 = 30 cm. Image height = 2.0 × 2 = 4.0 cm.

Answer: the image is 30 cm from the lens on the far side. It is real, inverted and magnified, with a magnification of 4.0 ÷ 2.0 = 2.0. This fits the table: the object is between F and 2F, so the image lies beyond 2F.

Do all courses use a lens equation?

No, and the ones that do write it differently. AQA GCSE Physics asks only for magnification from image and object heights, in its physics-only content. The Cambridge IGCSE syllabus works with ray diagrams and has no lens formula. The Punjab Class 10 textbook uses magnification but no lens formula either.

Where a lens formula is used, there are two common sign conventions:

  • Real is positive. Many UK A-level books write 1u+1v=1f\frac{1}{u} + \frac{1}{v} = \frac{1}{f}, with distances to real objects and images counted as positive. For worked example 3, 115+1v=110\frac{1}{15} + \frac{1}{v} = \frac{1}{10} gives v = +30 cm.
  • New Cartesian. Many Indian textbooks, including the NCERT books, write 1v−1u=1f\frac{1}{v} - \frac{1}{u} = \frac{1}{f}. Distances are measured from the lens, and those against the direction of the light are negative, so here u = −15 cm. This again gives v = +30 cm, and the magnification v ÷ u comes out as −2, where the minus sign means inverted.

The image is the same either way. Only the signs differ, so always use the convention your own course uses.

Common mistakes

  • Bending the parallel ray through the wrong F. A ray that arrives parallel to the axis passes through F on the far side of the lens.
  • Using solid lines for virtual rays. Rays traced back to a virtual image should be dashed.
  • Saying a virtual image can be projected. It cannot be caught on a screen.
  • Mixing units in magnification. Both heights must be in the same unit.
  • Thinking a converging lens always magnifies. For an object beyond 2F, the image is diminished.
  • Copying signs from a different convention. Learn one sign convention, the one your course uses.

Key points

  • A converging lens brings rays parallel to the axis together at the principal focus, F.
  • Use any two of the three standard rays: parallel then through F, straight through the centre, and through F then parallel.
  • An object outside F gives a real, inverted image. An object inside F gives a virtual, upright, magnified image.
  • Real images can be shown on a screen. Virtual images cannot, and are drawn with dashed lines.
  • Magnification = image height ÷ object height, with no unit.
  • Courses that use a lens formula do not all use the same sign convention.